View LM4651N_914241.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LM4651 & LM4652 OvertureTM 170W Class D Audio Power Amplifier Solution
January 2003
LM4651 & LM4652 OvertureTM Audio Power Amplifier 170W Class D Audio Power Amplifier Solution
General Description
The IC combination of the LM4651 driver and the LM4652 power MOSFET provides a high efficiency, Class D subwoofer amplifier solution. The LM4651 is a fully integrated conventional pulse width modulator driver IC. The IC contains short circuit, under voltage, over modulation, and thermal shut down protection circuitry. The LM4651also contains a standby function which shuts down the pulse width modulation minimizing supply current. The LM4652 is a fully integrated H-bridge power MOSFET IC in a TO-220 power package. The LM4652 has a temperature sensor built in to alert the LM4651 when the die temperature of the LM4652 exceeds the threshold. Together, these two IC's form a simple, compact high power audio amplifier solution complete with protection normally seen only in Class AB amplifiers. Few external components and minimal traces between the IC's keep the PCB area small and aids in EMI control. The near rail-to-rail switching amplifier substantially increases the efficiency compared to Class AB amplifiers. This high efficiency solution significantly reduces the heat sink size compared to a Class AB IC of the same power level. This two-chip solution is optimum for powered subwoofers and self powered speakers.
Key Specifications
n n n n Output power into 4 with < 10% THD. 170W (Typ) < 0.3% THD (Typ) THD at 10W, 4, 10 - 500Hz. Maximum efficiency at 125W 85% (Typ) > 100dB (Min) Standby attenuation.
Features
Conventional pulse width modulation. Externally controllable switching frequency. 50kHz to 200kHz switching frequency range. Integrated error amp and feedback amp. Turn-on soft start and under voltage lockout. Over modulation protection (soft clipping). Externally controllable output current limiting and thermal shutdown protection. n Self checking protection diagnostic. n n n n n n n
Applications
n Powered subwoofers for home theater and PC's n Car booster amplifier n Self-powered speakers
Connection Diagrams
LM4651 Plastic Package LM4652 Plastic Package (Note 8)
10127773
10127772
Top View Order Number LM4651N See NS Package Number N28B
Isolated TO-220 Package Order Number LM4652TF See NS Package Number TF15B or Non-Isolated TO-220 Package Order Number LM4652TA See NS Package Number TA15A
Overture (R) is a registered trademark of National Semiconductor Corporation.
(c) 2003 National Semiconductor Corporation
DS101277
www.national.com
LM4651 & LM4652
Absolute Maximum Ratings
2)
(Notes 1,
Supply Voltage |V+| + |V-| Thermal Resistance LM4651 N Package JA JC LM4652 TF, TO-220 Package JA JC LM4652 T, TO-220 Package JA JC
22V to 44V
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Output Current (LM4652) Power Dissipation (LM4651) (Note 3) Power Dissipation (LM4652) (Note 3) ESD Susceptibility (LM4651) (Note 4) LM4652 (pins 2,6,10,11) ESD Susceptibility (LM4651) (Note 5) LM4652 (pins 2,6,10,11) Junction Temperature (Note 6) Soldering Information N, TA and TF Package (10 seconds) Storage Temperature 260C -40C to + 150C
52C/W 22C/W
22V
10A 1.5W 32W 2000V 500V 200V 100V 150C
43C/W 2.0C/W
37C/W 1.0C/W
Operating Ratings (Notes 1, 2)
Temperature Range -40C TA +85C
System Electrical Characteristics for LM4651 and LM4652 (Notes 1, 2) The following specifications apply for +VCC = +20V, -VEE = -20V, f SW = 125kHz, fIN = 100Hz, RL = 4, unless otherwise specified. Typicals apply for TA = 25C. For specific circuit values, refer to Figure 1 (Typical Audio Application Circuit).
LM4651 & LM4652 Symbol Parameter Conditions VIN = 0V, IO = 0mA RDLY = 0 RDLY = 10k VPIN13 = 5V, Stby: On VPIN13 = 5V, Stby: On RL = 4, 1% THD RL = 4, 10% THD PO Output Power (Continuous Average) RL = 8, 1% THD RL = 8, 10% THD fSW = 75kHz, RL = 4, 1% THD fSW = 75kHz, RL = 4, 10% THD Efficiency at PO = 5W Efficiency (LM4651 & LM4652) Power Dissipation (LM4651 + LM4652) Total Harmonic Distortion Plus Noise Output Noise Signal-to-Noise Ratio Output Offset Voltage PO = 5W, RDLY = 5k Typical Limit (Note 7) ICQ ISTBY AM Total Quiescent Power Supply Current Standby Current Standby Attenuation 237 124 17 Units (Limits)
mA mA mA dB W W W W W W % % W W
> 115
125 155 75 90 135 170 55 85 22 22
PO = 125W, THD = 1% PO = 125W, THD = 1% (max) fSW = 75kHz, PO = 135W, THD = 1% (max) 10W, 10Hz fIN 500Hz, AV = 18dB 10Hz BW 80kHz A Weighted, no signal, RL = 4 A-Wtg, Pout = 125W, RL = 4 22kHz BW, Pout = 125W, RL = 4 VIN = 0V, IO = 0mA, ROFFSET = 0
Pd
THD+N eOUT SNR VOS
0.3 550 92 89 0.07
% V dB dB V
www.national.com
2
LM4651 & LM4652
System Electrical Characteristics for LM4651 and LM4652
(Notes 1, 2) (Continued) The following specifications apply for +VCC = +20V, -VEE = -20V, f SW = 125kHz, fIN = 100Hz, RL = 4, unless otherwise specified. Typicals apply for TA = 25C. For specific circuit values, refer to Figure 1 (Typical Audio Application Circuit). LM4651 & LM4652 Parameter Conditions RL = 4, 10Hz BW 30kHz +VCCAC = -VEEAC = 1VRMS, fAC = 120Hz Typical Limit (Note 7) Units (Limits)
Symbol
PSRR
Power Supply Rejection Ratio
37
dB
Electrical Characteristics for LM4651 (Notes 1, 2, 7)
The following specifications apply for +VCC = +20V, -VEE = -20V, fSW = 125kHz, unless otherwise specified. Limits apply for TA = 25C. For specific circuit values, refer to Figure 1 (Typical Audio Application Circuit). LM4651 & LM4652 Symbol Parameter Conditions LM4652 not connected, IO = 0mA, |VCC+| + |VEE-|, RDLY = 0 Not in Standby Mode In Standby Mode ROSC = 15k ROSC = 0 ROSC = 4k, fSW = 125kHz RDLY = 0 Pulse Width Measured at 50% 2.0 65 200 1 27 310 3 Typical Limit (Note 7) ICQ VIL VIH fSW fSWerror Tdead TOverMod Total Quiescent Current Standby Low Input Voltage Standby High Input Voltage Switching Frequency Range 50% Duty Cycle Error Dead Time Over Modulation Protection Time 36 15 45 0.8 2.5 Units (Limits) mA (min) mA (max) V (max) V (min) kHz kHz % (max) ns ns
Electrical Characteristics for LM4652 (Notes 1, 2, 7)
The following specifications apply for +VCC = +20V, -VEE = -20V, unless otherwise specified. Limits apply for TA = 25C. For specific circuit values, refer to Figure 1 (Typical Audio Application Circuit). LM4651 & LM4652 Symbol Parameter Drain-to-Source Breakdown Voltage Drain-to-Source Leakage Current Gate Threshold Voltage Static Drain-to-Source On Resistance Rise Time Fall Time Maximum Saturation Drain Current Conditions Typical Limit (Note 7) V(BR)DSS IDSS VGSth RDS(ON) tr tf ID VGS = 0 VDS = 44VDC, VGS = 0V VDS = VGS, ID = 1mADC VGS = 6VDC, ID = 6ADC VGD = 6VDC, VDS = 40VDC, RGATE = 0 VGD = 6VDC, VDS = 40VDC, RGATE = 0 VGS = 6VDC, VDS = 10VDC 55 1.0 0.85 200 25 26 10 8 300 Units (Limits) V mA V m (max) ns ns ADC (min)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 2: All voltages are measured with respect to the GND pin unless otherwise specified. Note 3: For operating at case temperatures above 25C, the LM4651 must be de-rated based on a 150C maximum junction temperature and a thermal resistance of JA = 62 C/W (junction to ambient), while the LM4652 must be de-rated based on a 150C maximum junction temperature and a thermal resistance of JC = 2.0 C/W (junction to case) for the isolated package (TF) or a thermal resistance of JC = 1.0C/W (junction to case) for the non-isolated package (T). Note 4: Human body model, 100 pF discharged through a 1.5 k resistor. Note 5: Machine Model, 220pF-240pF discharge through all pins. Note 6: The operating junction temperature maximum, Tjmax is 150C. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
3
www.national.com
LM4651 & LM4652
Electrical Characteristics for LM4652 (Notes 1, 2, 7)
(Continued)
Note 8: The LM4652TA package TA15A is a non-isolated package, setting the tab of the device and the heat sink at -V potential when the LM4652 is directly mounted to the heat sink using only thermal compound. If a mica washer is used in addition to thermal compound, CS (case to sink) is increased, but the heat sink will be isolated from -V.
10127768
FIGURE 1. Typical Application Circuit and Test Circuit
www.national.com
4
LM4651 & LM4652
LM4651 Pin Descriptions
Pin No. 1 2,27 3 4 5,15 6 7 8 9 10 11 12 13 14 16 17 18 19 20,21 22,23 24 25 26 28 Symbol OUT1 BS1,BS2 HG1 HG2 GND +6VBYP +VCC -6VBYP FBKVO ERRIN ERRVO TSD STBY FBK1 OSC Delay SCKT FBK2 -VDDBYP -VEE START LG1 LG2 OUT2 Description The reference pin of the power MOSFET output to the gate drive circuitry. The bootstrap pin provides extra bias to drive the upper gates, HG1,HG2. High-Gate #1 is the gate drive to a top side MOSFET in the H-Bridge. High-Gate #2 is the gate drive to a top side MOSFET in the H-Bridge. The ground pin for all analog circuitry. The internally regulated positive voltage output for analog circuitry. This pin is available for internal regulator bypassing only. The positive supply input for the IC. The internally regulated negative voltage output for analog circuitry. This pin is available for internal regulator bypassing only. The feedback instrumentation amplifier output pin. The error amplifier inverting input pin. The input audio signal and the feedback signal are summed at this input pin. The error amplifier output pin. The thermal shut down input pin for the thermal shut down output of the LM4652. Standby function input pin. This pin is CMOS compatible. The feedback instrumentation amplifier pin. This must be connected to the feedback filter from VO1 (pin 15 on the LM4652 ). The switching frequency oscillation pin. Adjusting the resistor from 15.5k to 0 changes the switching frequency from 75kHz to 225kHz. The dead time setting pin. Short circuit setting pin. Minimum setting is 10A. The feedback instrumentation amplifier pin. This must be connected to the feedback filter from VO2 (pin 7 on the LM4652 ). The regulator output for digital blocks. This pin is for bypassing only. The negative voltage supply pin for the IC. The start up capacitor input pin. This capacitor adjusts the start up time of the diagnostic sequence for the modulator. Refer to Start up Sequence and Timing in the Application Information section. Low-Gate #1 is the gate drive to a bottom side MOSFET in the H-Bridge. Low-Gate #2 is the gate drive to a bottom side MOSFET in the H-Bridge. The reference pin of the power MOSFET output to the gate drive circuitry.
5
www.national.com
LM4651 & LM4652
LM4652 Pin Descriptions
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Symbol GND LG1 -VEE TSD NC LG2 VO2 NC NC HG2 NC NC +VCC HG1 VO2 Description A ground reference for the thermal shut down circuitry. Low-Gate #1 is the gate input to a bottom side MOSFET in the H-Bridge. The negative voltage supply input for the power MOSFET H-Bridge. The thermal shut down flag pin. This pin transitions to 6V when the die temperature exceeds 150C. No connection Low-Gate #2 is the gate input to a bottom side MOSFET in the H-Bridge. The switching output pin for one side of the H-Bridge. No connection. No connection. High-Gate #2 is the gate input to a top side MOSFET in the H-Bridge. No connection. No connection. The positive voltage supply input for the power MOSFET H-Bridge. High-Gate #1 is the gate input to a top side MOSFET in the H-Bridge. The switching output pin for one side of the H-Bridge.
Note: NC, no connect pins are floating pins. It is best to connect the pins to GND to minimize any noise from being coupled into the pins.
External Components Description
Components 1. 2. 3. 4. 5. R1 R2 Rf Cf RfI1
(Refer to Figure 1) Functional Description
Works with R2, Rfl1 and Rfl2 to set the gain of the system. Gain = {[R2/(R1 + 100)] x [(Rfl1 + Rfl2)/Rfl2] - [R2/(R1 + 100)] + 0.5} + [(VCC - 20) * 0.0175] (V/V). See description above for R1. Sets the gain and bandwidth of the system by creating a low pass filter for the Error Amplifier's feedback with Cf. 3dB pole is at fC = 1/(2RfCf) (Hz). See description above for Rf. Provides a reduction in the feedback with RfI2. RfI1should be 10 X RfI2 minimum to reduce effects on the pole created by RfI2 and CfI1. See also note for R1, R2 for effect on System Gain. RfI2 and CfI1 creates a low pass filter with a pole at fC = 1/(2RfI2CfI1) (Hz). See also note for R1, R2 for effect on System Gain. See description above for RfI2. Establish the second pole for the low pass filter in the feedback path at fC = 1/(2RfI3CfI2) (Hz). See description above for RfI3. Combined with CBYP creates a 2-pole, low pass output filter that has a -3dB pole at fC = 1/{2[L1(2CBYP + C1)]1/2} (Hz). Filters the commom mode high frequency noise from the amplifier's outputs to GND. Recommended value is 0.1F to 1F. See description for L1. Bypass capacitors for VCC, VEE, analog and digital voltages (VDD, +6V, -6V). See Supply Bypassing and High Frequency PCB Design in the Application Information section for more information. Provides the bootstrap capacitance for the boot strap pin. Sets the dead time or break before make time to TDLY = (1.7x10-12)(500 + RDLY) (seconds) or RDLY = [TDLY/(1.7x10-12)] - 500 (). Controls the startup time with TSTART = (8.5x104) CSTART (seconds) or CSTART = TSTART /(8.5x104) (F).
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
RfI2 CfI1 RfI3 CfI2 L1 C1 Cbyp CB1-CB4 CBT RDLY CSTART
www.national.com
6
LM4651 & LM4652
External Components Description (Refer to Figure 1)
17. 18. 19. 20. 21. 22. 23. RSCKT ROSC D1
(Continued)
Sets the output current limit with ISCKT = (1x105)/(10k \ RSCKT) (A) or RSCKT = [(1x109)/ISCKT] / [10k - (1x105/ISCKT)] (). Controls the switching frequency with fSW = 1x109 / (4000 + ROSC) (Hz) or ROSC = (1x109/fSW) - 4000 (). Schottky diode to protect the output MOSFETs from fly back voltages.
CSBY1, CSBY2, CSBY3 Supply de-coupling capacitors. See Supply Bypassing in the Application Information section. ROFFSET CIN Rgate Provides a small DC voltage at the input to minimize the output DC offset seen by the load. This also minimize power on pops and clicks. Blocks DC voltages from being coupled into the input and blocks the DC voltage created by ROFFSET from the source. Slows the rise and fall time of the gate drive voltages that drive the output FET's.
Typical Performance Characteristics
Output Power vs. Supply Voltage Output Power vs. Supply Voltage
10127704
10127705
THD+N vs. Output Power RL = 4
THD+N vs. Output Power RL = 8
10127706
10127707
7
www.national.com
LM4651 & LM4652
Typical Performance Characteristics
THD+N vs. Output Power RL = 4
(Continued) THD+N vs. Output Power RL = 8
10127708
10127709
THD+N vs. Frequency vs. Bandwidth RL = 4
THD+N vs. Frequency vs. Bandwidth RL = 8
10127710
10127711
THD+N vs. Frequency vs. Bandwidth RL = 4
THD+N vs. Frequency vs. Bandwidth RL = 8
10127712
10127713
www.national.com
8
LM4651 & LM4652
Typical Performance Characteristics
Power Dissipation & Efficiency vs. Output Power
(Continued) Clipping Power Point & Efficiency vs. Switching Frequency (fSW)
10127716
10127717
Frequency Response RL = 4
Supply Current vs. Switching Frequency (LM4651 & LM4652)
10127718
10127720
Supply Current vs. Supply Voltage (LM4651 & LM4652)
RDS(ON) vs. Temperature
10127721
10127723
9
www.national.com
LM4651 & LM4652
Application Information
GENERAL FEATURES System Functional Information: The LM4651 is a conventional pulse width modulator/driver. As Figure 2 shows the incoming audio signal is compared with a triangle waveform with a much higher frequency than the audio signal (not drawn to scale). The comparator creates a variable duty cycle squarewave. The squarewave has a duty cycle proportional to the audio signal level. The squarewave is then properly conditioned to drive the gates of power MOSFETs in an H-bridge configuration, such as the LM4652. The pulse train of the power MOSFETs are then fed into a low pass filter (usually a LC) which removes the high frequency and delivers an amplified replica of the audio input signal to the load. The value of CSTART sets the time it takes for the IC to go though the start-up sequence and the frequency that the diagnostic circuitry checks to see if an error condition has been corrected. An Error condition occurs if current limit, thermal shut down, under voltage detection, or standby are sensed. The self-diagnostic circuit checks to see if any one of these error flags has been removed at a frequency set by the CSTART capacitor. For example, if the value of CSTART is 10F then the diagnostic circuitry will check approximately every second to see if an error condition has been corrected. If the error condition is no longer present, the LM4651/52 will return to normal operation.
10127701 10127770
FIGURE 2. Conventional Pulse Width Modulation
FIGURE 3. Startup Timing Diagram Standby Function: The standby function of the LM4651 is CMOS compatible, allowing the user to perform a muting of the music as well as turning off all power MOSFETs by shutting down the pulse width waveform. Standby has the added advantage of minimizing the quiescent current. Because standby shuts down the pulse width waveform, the attenuation of the music is complete ( > 120dB), EMI is minimized, and any output noise is eliminated since there is no modulation waveform. By placing a logic "1" or 5V at pin 13, the standby function will be enabled. A logic "0" or 0V at pin 13 will disable the standby function allowing modulation by the input signal. Under Voltage Protection: The under voltage protection disables the output driver section of the LM4651 while the supply voltage is below 10.5V. This condition can occur as power is first applied or when low line, changes in load resistance or power supply sag occurs. The under voltage protection ensures that all power MOSFETs are off, eliminating any shoot-through current and minimizing pops or clicks during turn-on and turn-off. The under voltage protection gives the digital logic time to stabilize into known states providing a popless turn on. Start Up Sequence and Self-Diagnostic Timing: The LM4651 has an internal soft start feature (see Figure 3) that ensures reliable and consistent start-up while minimizing turn-on thumps or pops. During the start-up cycle the system is in standby mode. This start-up time is controlled externally by adjusting the capacitance (CSTART) value connected to the START pin. The start-up time can be controlled by the capacitor value connected to the START pin given by Equation (1) or (2): tSTART = (8.4x104)CSTART CSTART = TSTART/(8.5x104)
www.national.com
Current Limiting and Short Circuit Protection: The resistor value connected between the SCKT pin and GND determines the maximum output current. Once the output current is higher than the set limit, the short circuit protection turns all power MOSFETs off. The current limit is set to a minimum of 10A internally but can be increased by adjusting the value of the RSCKT resistor. Equation (3) shows how to find RSCKT. ISCKT = 1X105/(10k\ RSCKT) (Amps) (3)
This feature is designed to protect the MOSFETs by setting the maximum output current limit under short circuit conditions. It is designed to be a fail-safe protection when the output terminals are shorted or a speaker fails and causes a short circuit condition. Thermal Protection The LM4651 has internal circuitry (pin 12) that is activated by the thermal shutdown output signal from the LM4652 (pin 4). The LM4652 has thermal shut down circuitry that monitors the temperature of the die. The voltage on the TSD pin (pin 4 of the LM4652) goes high (6V) once the temperature of the LM4652 die reaches 150C. This pin should be connected directly to the TSD pin of the LM4651 (pin 12). The LM4651 disables the pulse width waveform when the LM4652 transmits the thermal shutdown flag. The pulse width waveform remains disabled until the TSD flag from the LM4652 goes low, signaling the junction temperature has cooled to a safe level. Dead Time Setting The DELAY pin on the LM4651 allows the user to set the amount of dead time or break before make of the system. This is the amount of time one pair of FETs are off before another pair is switched on. Increased dead time will reduce the shoot through current but has the disadvantage of increasing THD. The dead time should be
10
(seconds) (Farads)
(1) (2)
LM4651 & LM4652
Application Information
(Continued) Feedback Amplifier and Filter: The purpose of the feedback amplifier is to differentially sample the output and provide a single-ended feedback signal to the error amplifier to close the feedback loop. The feedback is taken directly from the switching output before the demodulating LC filter to avoid the phase shift caused by the output filter. The signal fed back is first low pass filtered with a single pole or dual pole RC filter to remove the switching frequency and its harmonics. The differential signal, derived from the bridge output, goes into the high input impedance instrumentation amplifier that is used as the feedback amplifier. The instrumentation amplifier has an internally fixed gain of 1. The use of an instrumentation amplifier serves two purposes. First, it's input are high impedance so it doesn't load down the output stage. Secondly, an IA has excellent common-mode rejection when its gain setting resistors are properly matched. This feature allows the IA to derive the true feedback signal from the differential output, which aids in improving the system performance.
reduced as the desired bandwidth of operation increases. The dead time can be adjusted with the RDLY resistor by Equation (4): TDLY = 1.7x10-12 (500 + RDLY) (Seconds) (4)
Currently, the recommended value is 5k. Oscillator Control: The modulation frequency is set by an external resistor, ROSC, connected between pin 16 and GND. The modulation frequency can be set within the range of 50kHz to 225kHz according to the design requirements. The values of ROSC and fOSC can be found by Equation (5) and (6): (Hz) (5) fOSC = 1x109/ (4000 + ROSC) ROSC = (1x109/ fOSC) - 4000 () (6)
Equations (5) and (6) are for RDLY = 0. Using a value of RDLY greater than zero will increase the value needed for ROSC. For RDLY = 5k, ROSC will need to be increased by about 2k. As the graphs show, increasing the switching frequency will reduce the THD but also decreases the efficiency and maximum output power level before clipping. Increasing the switching frequency increases the amount of loss because switching currents lower the efficiency across the output power range. A higher switching frequency also lowers the maximum output power before clipping or the 1% THD point occur. Over-Modulation Protection: The over-modulation protection is an internally generated fixed pulse width signal that prevents any side of the H-bridge power MOSFETs from remaining active for an extended period of time. This condition can result when the input signal amplitude is higher than the internal triangle waveform. Lack of an over modulation signal can increase distortion when the amplifier's output is clipping. Figure 4 shows how the over modulation protection works.
10127703
FIGURE 5. Feedback instrumentation Amplifier Schematic
Error Amplifier: The purpose of the error amplifier is to sum the input audio signal with the feedback signal derived from the output. This inverting amplifier's gain is externally configurable by resistors Rf and R1. The parallel feedback capacitor and resistor form a low pass filter that limits the frequency content of the input audio signal and the feedback signal. The pole of the filter is set by Equation (7). fIP = 1/(2RfCf) (Hz) (7)
10127702
FIGURE 4. Over Modulation Protection
The over modulation protection also provides a "soft clip" type response on the top of a sine wave. This minimum pulse time is internally set and cannot be adjusted. As the switching frequency increases this minimum time becomes a higher percentage of the period (TPERIOD = 1/fSW). Because the over modulation protection time is a higher percentage of the period, the peak output voltage is lower and, therefore, the output power at clipping is lower for the same given supply rails and load.
11
On-Board Regulators: The LM4651 has its own internal supply regulators for both analog and digital circuits. Separate 6V regulators exist solely for the analog amplifiers, oscillator and PWM comparators. A separate voltage regulator powers the digital logic that controls the protection, level shifting, and high-/low-side driver circuits. System performance is enhanced by bypassing each regulator's output. The 6V regulator outputs, labeled +6VBYP (pin 6) and -6VBYP (pin 8) should be bypassed to ground. The digital regulator output, -VDDBYP (pins 20 & 21) should be bypassed to -VEE (pins 22 & 23). The voltage level of -VDDBYP should be always be 6V closer to ground than the negative rail, -VEE. As an example, if -VEE = -20V, then -VDDBYP should equal -14V. Recommended capacitor values and type can be found in Figure 1, Typical audio Application Circuit.
www.national.com
LM4651 & LM4652
Application Information
APPLICATIONS HINTS Introduction
(Continued)
National Semiconductor (NSC) is committed to providing application information that assists our customers in obtaining the best performance possible from our products. The following information is provided in order to support this commitment. The reader should be aware that the optimization of performance was done using a reference PCB designed by NSC and shown in Figure 7 through Figure 11. Variations in performance can occur because of physical changes in the printed circuit board and the application. Therefore, the designer should know that component value changes may be required in order to optimize performance in a given application. The values shown in this data sheet can be used as a starting point for evaluation purposes. When working with high frequency circuits, good layout practices are also critical to achieving maximum performance. Input Pre-Amplifier with Subwoofer Filter The LM4651 and LM4652 Class D solution is designed for low frequency audio applications where low gain is required. This necessitates a pre-amplifier stage with gain and a low pass audio filter. An inexpensive input stage can be designed using National's LM833 audio operational amplifier and a minimum number of external components. A gain of 10 (20dB) is recommended for the pre-amplifier stage. For a subwoofer application, the pole of the low pass filter is normally set within the range of 60Hz - 180Hz. For a clean sounding subwoofer the filter should be at least a secondorder filter to sharply roll off the high frequency audio signals. A higher order filter is recommended for stand-alone selfpowered subwoofer applications. Figure 6 shows a simple input stage with a gain of 10 and a second-order low pass filter.
pacitors (1F to 10F) in parallel will do an adequate job of removing most noise from the supply rails. These capacitors should be placed as close as possible to each IC's supply pin(s) using leads as short as possible. For supply stabilizing, large electrolytic capacitors (3,300F to 15,000F) are needed. The value used is design and cost dependent. High Frequency PCB Design A double-sided PCB is recommended when designing a class D amplifier system. One side should contain a ground plane with the power traces on the other side directly over the ground plane. The advantage is the parasitic capacitance created between the ground plane and the power planes. This parasitic capacitance is very small (pF) but is the value needed for coupling high frequency noise to ground. At high frequencies, capacitors begin to act more like inductors because of lead and parasitic inductance in the capacitor. For this reason, bypassing capacitors should be surface mount because of their low parasitic inductance. Equation (8) shows how to determine the amount of power to ground plane capacitance. C = eoerA/d (Farads) where eo = 0.22479pF/in and er = 4.1 (8)
A is the common PCB area and d is the distance between the planes. The designer should target a value of 100pF or greater for both the positive supply to ground capacitance and negative supply to ground capacitance. Signal traces that cross over each other should be laid out at 90 to minimized any coupling. Output Offset Voltage Minimization The amount of DC offset voltage seen at the output with no input signal present is already quite good with the LM4651/ 52. With no input signal present the system should be at 50% duty cycle. Any deviation from 50% duty cycle creates a DC offset voltage seen by the load. To completely eliminate the DC offset, a DC voltage divider can be used at the input to set the DC offset to near zero. This is accomplished by a simple resistor divider that applies a small DC voltage to the input. This forces the duty cycle to 50% when there is no input signal. The result is a LM4651 and LM4652 system with near zero DC offset. The divider should be a 1.8M from the +6V output (pin 6) to the input (other side of 25k, R1). R1 acts like the second resistor in the divider. Also use a 1F input capacitor before R1 to block the DC voltage from the source. R1 and the 1F capacitor create a high pass filter with a 3dB point at 6.35Hz. The value of ROFFSET is set according to the application. Variations in switching frequency and supply voltage will change the amount of offset voltage requiring a different value than stated above. The value above (1.8M) is for 20V and a switching frequency of 125kHz. Output Stage Filtering As common with Class D amplifier design, there are many trade-offs associated with different circuit values. The output stage is not an exception. National has found good results with a 50F inductor and a 5F Mylar capacitor (see Figure 1, Typical Audio Application Circuit) used as the output LC filter. The two-pole filter contains three components; L1
10127777
FIGURE 6. Pre-amplifier Stage with Low Pass Filter
Supply Bypassing Correct supply bypassing has two important goals. The first is to ensure that noise on the supply lines does not enter the circuit and become audible in the output. The second is to help stabilize an unregulated power supply and provide current under heavy current conditions. Because of the two different goals multiple capacitors of various types and values are recommended for supply bypassing. For noise decoupling, generally small ceramic capacitors (.001F to .1F) along with slightly larger tantalum or electrolytic cawww.national.com 12
LM4651 & LM4652
Application Information
1
(Continued)
and CBYP because the LM4651 and LM4652 have a bridged output. The design formula for a bridge output filter is fC = 1/{2[L1(2CBYP + C1)] 2} (Hz). A common mistake is to connect a large capacitor between ground and each output. This applies only to single-ended applications. In bridge operation, each output sees CBYP. This causes the extra factor of 2 in the formula. The alternative to CBYP is a capacitor connected between each output, VO, and VO2, and ground. This alternative is, however, not size or cost efficient because each capacitor must be twice CBYP's value to achieve the same filter cutoff frequency. The additional small value capacitors connected between each output and ground (C1) help filter the high frequency from the output to ground . The recommended value for C1 is 0.1F to 1F or 2% to 20% of CBYP." Modulation Frequency Optimization Setting the modulation frequency depends largely on the application requirements. To maximize efficiency and output power a lower modulation frequency should be used. The lower modulation frequency will lower the amount of loss caused by switching the output MOSFETs increasing the efficiency a few percent. A lower switching frequency will also increase the peak output power before clipping because the over modulation protection time is a smaller percentage of the total period. Unfortunately, the lower modulation frequency has worse THD+N performance when the output power is below 10 watts. The recommended switching frequency to balance the THD+N performance, efficiency and output power is 125kHz to 145kHz. THD+N Measurements and Out of Audio Band Noise THD+N (Total Harmonic Distortion plus Noise) is a very important parameter by which all audio amplifiers are measured. Often it is shown as a graph where either the output power or frequency is changed over the operating range. A very important variable in the measurement of THD+N is the bandwidth limiting filter at the input of the test equipment. Class D amplifiers, by design, switch their output power devices at a much higher frequency than the accepted audio range (20Hz - 20kHz). Switching the outputs makes the amplifier much more efficient than a traditional Class A/B amplifier. Switching the outputs at high frequency also increases the out-of-band noise. Under normal circumstances this out-of-band noise is significantly reduced by the output low pass filter. If the low pass filter is not optimized for a given switching frequency, there can be significant increase in out-of-band noise. THD+N measurements can be significantly affected by outof-band noise, resulting in a higher than expected THD+N measurement. To achieve a more accurate measurement of THD, the bandwidth at the input of the test equipment must be limited. Some common upper filter points are 22kHz, 30kHz, and 80kHz. The input filter limits the noise component of the THD+N measurement to a smaller bandwidth resulting in a more real-world THD+N value. The output low pass filter does not remove all of the switching fundamental and harmonics. If the switching frequency
fundamental is in the measurement range of the test equipment, the THD+N measurement will include switching frequency energy not removed by the output filter. Whereas the switching frequency energy is not audible, it's presence degrades the THD+N measurement. Reducing the bandwidth to 30kHz and 22kHz reveals the true THD performance of the Class D amplifier. Increasing the switching frequency or reducing the cutoff frequency of the output filter will also reduce the level of the switching frequency fundamental and it's harmonics present at the output. This is caused by a switching frequency that is higher than the output filter cutoff frequency and, therefore, more attenuation of the switching frequency. In-band noise is higher in switching amplifiers than in linear amplifiers because of increased noise from the switching waveform. The majority of noise is out of band (as discussed above), but there is also an increase of audible noise. The output filter design (order and location of poles) has a large effect on the audible noise level. Power supply voltage also has an effect on noise level. The output filter removes a certain amount of the switching noise. As the supply increases, the attenuation by the output fiter is constant. However, the switching waveform is now much larger resulting in higher noise levels. THERMAL CONSIDERATIONS Heat Sinking The choice of a heat sink for the output FETs in a Class D audio amplifier is made such that the die temperature does not exceed TJMAX and activate the thermal protection circuitry under normal operating conditions. The heat sink should be chosen to dissipate the maximum IC power which occurs at maximum output power for a given load. Knowing the maximum output power, the ambient temperature surrounding the device, the load and the switching frequency, the maximum power dissipation can be calculated. The additional parameters needed are the maximum junction temperature and the thermal resistance of the IC package (JC, junction to case), both of which are provided in the Absolute Maximum Ratings and Operating Ratings sections above. It should be noted that the idea behind dissipating the power within the IC is to provide the device with a low resistance to convection heat transfer such as a heat sink. Convection cooling heat sinks are available commercially and their manufacturers should be consulted for ratings. It is always safer to be conservative in thermal design. Proper IC mounting is required to minimize the thermal drop between the package and the heat sink. The heat sink must also have enough metal under the package to conduct heat from the center of the package bottom to the fins without excessive temperature drop. A thermal grease such as Wakefield type 120 or Thermalloy Thermacote should be used when mounting the package to the heat sink. Without some thermal grease, the thermal resistance CS (case to sink) will be no better than 0.5C/W, and probably much worse. With the thermal grease, the thermal resistance will be 0.2C/W or less. It is important to properly torque the mounting screw. Over tightening the mounting screw will cause the package to warp and reduce the contact area with the heat sink. It can also crack the die and cause failure of the IC. The recommended maximum torque applied to the mounting screw is 40 inch-lbs. or 3.3 foot-lbs.
13
www.national.com
LM4651 & LM4652
Application Information
(Continued)
Determining Maximum Power Dissipation Power dissipation within the integrated circuit package is a very important parameter. An incorrect maximum power dissipation (PD) calculation may result in inadequate heat sinking, causing thermal shutdown circuitry to operate intermittently. There are two components of power dissipation in a class D amplifier. One component of power dissipation in the LM4652 is the RDS(ON) of the FET times the RMS output current when operating at maximum output power. The other component of power dissipation in the LM4652 is the switching loss. If the output power is high enough and the DC resistance of the filter coils is not minimized then significant loss can occur in the output filter. This will not affect the power dissipation in the LM4652 but should be checked to be sure that the filter coils with not over heat. The first step in determining the maximum power dissipation is finding the maximum output power with a given voltage and load. Refer to the graph Output Power verses Supply Voltage to determine the output power for the given load and supply voltage. From this power, the RMS output current can be calculated as IOUTRMS = SQRT(POUT/RL). The power dissipation caused by the output current is PDOUT = (IOUTRMS)2 * (2 * RDS(ON)). The value for RDS(ON) can be found from the Electrical Characteristics for the LM4652 table above. The percentage of loss due to the switching is calculated by Equation (9): %LOSSSWITCH = (tr+ tf + TOVERMOD) * fSW (9)
have calculated PDMAX and TAMBIENTMAX, we only need SA, the heat sink's thermal resistance. The following equation is derived from Equation (11): SA = [(TJMAX - TAMBIENTMAX) / PDMAX] - JC - CS Again, it must be noted that the value of SA is dependent upon the system designer's application and its corresponding parameters as described previously. If the ambient temperature surrounding the audio amplifier is higher than TAMBIENTMAX, then the thermal resistance for the heat sink, given all other parameters are equal, will need to be lower. Example Design of a Class D Amplifier The following is an example of how to design a class D amplifier system for a power subwoofer application utilizing the LM4651 and LM4652 to meet the design requirements listed below:
* * * * *
Output Power, 1% THD Load Impedance Input Signal level Input Signal Bandwidth Ambient Temperature
125W 4 3V RMS (max) 10Hz - 150Hz 50C (max)
tr, tf and TOVERMOD can be found in the Electrical Characteristic for the LM4651 and Electrical Characteristic for the LM4652 sections above. The system designer determines the value for fSW (switching frequency). Power dissipation caused by switching loss is found by Equation (10). POUTMAX is the 1% output power for the given supply voltage and the load impedance being used in the application. POUTMAX can be determined from the graph Output Power vs. Supply Voltage in the Typical Performance Characteristics section above. PDSWITCH = (%LOSSSWITCH * POUTMAX) / (1-%LOSSSWITCH) (Watts)
Determine the Supply Voltage From the graph Output Power verses Supply voltage at 1% THD the supply voltage needed for a 125 watt, 4 application is found to be 20V. Determine the Value for ROSC(Modulation Frequency) The oscillation frequency is chosen to obtain a satisfactory efficiency level while also maintaining a reasonable THD performance. The modulation frequency can be chosen using the Clipping Power Point and Efficiency verses Switching Frequency graph. A modulation frequency of 125kHz is found to be a good middle ground for THD performance and efficiency. The value of the resistor for ROSC is found from Equation (6) to be 3.9 k. Determine the Value for RSCKT (Circuit Limit) The current limit is internally set as a failsafe to 10 amps. The inductor ripple current and the peak output current must be lower than 10 amps or current limit protection will turn on. A typical 4 load driven by a filter using 50H inductors does not require more than 10A. The current limit will have to be increased when loads less than 4 are used to acheive higher output power. With RSCKT equal to 100k, the current limit is 10A. Determine the Value for RDLY (Dead Time Control) The delay time or dead time is set to the recommended value so RDLY equals 5k. If a higher bandwidth of operation is desired, RDLY should be a lower value resistor. If a zero value for RDLY is desired, connect the LM4651's pin 17 to GND. Determine the Value of L1, CBYP, C1, Rfl1 Rfl2, Cfl1 Cfl2, Rf, Cf (the Output and Feedback Filters) All component values show in Figure 1 Typical Audio Application Circuit, are optimized for a subwoofer application.
14
(10)
PDMAX for the LM4652 is found by adding the two components (PDSWITCH + PDOUT) of power dissipation together. Determining the Correct Heat Sink Once the LM4652's power dissipation known, the maximum thermal resistance (in C/W) of a heat sink can be calculated. This calculation is made using Equation (11) and is based on the fact that thermal heat flow parameters are analogous to electrical current flow properties. PDMAX = (TJMAX - TAMBIENTMAX) / JA (Watts) (11) Where JA = JC + CS + SA Since we know JC, CS, and TJMAX from the Absolute Maximum Ratings and Operating Ratings sections above (taking care to use the correct JC for the LM4652 depending on which package type is being used in the application) and
www.national.com
LM4651 & LM4652
Application Information
(Continued)
Use the following guidelines when changing any component values from those shown. The frequency response of the output filter is controlled by L1 and CBYP. Refer to the Application Information section titled Output Stage Filtering for a detailed explanation on calculating the correct values for L1 and CBYP. C1 should be in the range of 0.1F to 1F or 2 - 20% of CBYP. Rfl1 and Rfl2 are found by the ratio Rfl1 = 10Rfl2. A lower ratio can be used if the application is for lower output voltages than the 125Watt, 4 solution show here. The feedback RC filter's pole location should be higher than the output filter pole. The reason for two capacitors in parallel instead of one larger capacitor is to reduce the possible EMI from the feedback traces. Cfl1 is placed close as possible to the output of the LM4652 so that an audio signal is present on the feedback trace instead of a high frequency square wave. Cfl2 is then placed as close as possible to the feedback inputs (pins 14, 19) of the LM4651 to filter off any noise picked up by the feedback traces. The combination lowers EMI and provides a cleaner audio feedback signal to the LM4651. Rf should be in range of 100k to1M. Cf controls the bandwidth of the error signal and should be in the range of 100pF to 470pF. Determine the Value for CSTART (Start Up Delay) The start-up delay is chosen to be 1 second to ensure minimum pops or clicks when the amplifier is powered up. Using Equation (2), the value of CSTART is 11.7F. A standard value of 10F is used. Determine the Value of Gain, R1, and R2 The gain is set to produce a 125W output at no more than 1% distortion with a 3VRMS input. A dissipation of 125W in a 4 load requires a 22.4VRMS signal. To produce this output signal, the LM4651/LM4652 amplifier needs an overall closed-loop gain of 22.4VRMS/3VRMS, or 7.5V/V (17.5db). Equation (12) shows all the variables that affect the system gain. Gain = {[R2/(R1 + 100)] x [(Rfl1 + Rfl2)/Rfl2] - [R2/(R1 + (12) 100)] + 0.5} + [(VCC - 20) * 0.0175] (V/V) The values for RfI1, RfI2, and Rf were found in the Determine the Value of the Filters section above and shown in Figure 1. Therefore, RfI1 = 620k, RfI2 = 62k and Rf = 390k. The value of VCC was also found as the first step in this example to be 20V. Inserting these values into equation (12) and reducing gives the equation below: R2 = 0.7(R1 + 100) The input resistance is desired to be 20k so R1 is set to 20k. R2 is then found to require a value of 14.1k. Standard resistor values are 14.0k giving a gain of 7.43V/V or 14.3k giving a gain of 7.58V/V. Lowering R2 direcly affects the noise of the system. Changing R1 to increase gain with the lower value for R2 has very little affect on the noise level. The percent change in noise is about what whould be expected with a higher gain. The drawback to a lower R1 value is a larger CIN value, necessary to properly couple the lowest desired signal frequen15
cies. If a 20k input impedance is not required, then the recommended values shown in Figure 1, Typical Audio Application Circuit should be used: with R1's value set to 4.7k and then using a value of 3.4k for R2 for a gain of 7.5V/V. Determine the Needed Heat Sink The only remaining design requirement is a thermal design that prevents activating the thermal protection circuitry. Use Equations (9) - (11) to calculate the amount of power dissipation for the LM4652. The appropriate heat sink size, or thermal resistance in C/W, will then be determined. Equation (9) determines the percentage of loss caused by the switching. Use the typical values given in the Electrical Characteristics for the LM4651 and Electrical Characteristics for the LM4652 tables for the rise time, fall time and over modulation time: %Loss = (25ns+26ns+350ns) * 125kHz %Loss = 5.0% This switching loss causes a maximum power dissipation, using Equation (10), of: PDSWITCH = (5.0% * 125W) / (1-5.0%) PDSWITCH = 6.6W Next the power dissipation caused by the RDS(ON) of the output FETs is found by multiplying the output current times the RDS(ON). Again, the value for RDS(ON) is found from the Electrical Characteristics for the LM4652 table above. The value for RDS(ON) at 100C is used since we are calculating the maximum power dissipation. IOUTRMS = SQRT(125watts/4) = 5.59 amps PRDS(ON) = (5.59A)2 * (0.230*2) PRDS(ON) = 14.4W The total power dissipation in the LM4652 is the sum of these two power losses giving: PDTOTAL = 6.6W + 14.4W = 21W The value for Maximum Power Dissipation given in the System Electrical Characteristics for the LM4651 and LM4652 is 22 watts. The difference is due to approximately 1 watt of power loss in the LM4651. The above calculations are for the power loss in the LM4652. Lastly, use Equation (11) to determine the thermal resistance of the LM4652's heat sink. The values for JC and TJMAX are found in the Operating Ratings and the Absolute Maximum Ratings section above for the LM4652. The value of JC is 2C/W for the isolated (TF) package or 1C/W for the non-isolated (T) package. The value for TJMAX is 150C. The value for CS is set to 0.2C/W since this is a reasonable value when thermal grease is used. The maximum ambient temperature from the design requirements is 50. The value of SA for the isolated (TF) package is: SA = [(150C - 50C)/21W] - 2C/W - 0.2C/W SA = 2.5C/W
www.national.com
LM4651 & LM4652
Application Information
(Continued)
SA = 3.5C/W To account for the use of a mica washer simply subtract the thermal resistance of the mica washer from SA calculated above.
and for the non-isolated (T) package without a mica washer to isolate the heat sink from the package: SA = [(150C - 50C)/21W] - 1C/W - 0.2C/W
Recommendations for Critical External Components Circuit Symbol CfI1 CfI2 Cf CB2 CB1 & CBT CB3 C2 Suggested Value 330pF 100pF 470pF 1.0F - 10F 0.1F 0.001F 0.1F 0.1F - 1.0F Suggested Type Ceramic Disc Ceramic Disc Ceramic Disc Resin Dipped Solid Tantalum Monolithic Ceramic Monolithic Ceramic Metallized Polypropylene or Polyester Film Metallized Polypropylene or Polyester Film Metallized Polypropylene or Polyester Film Fast Schottky Diode High Current Toroid Inductor (with header) High Saturation Open Core (Vertical Mount Power Chokes) High Saturation Flux Density Ferrite Rod High Saturation Flux Density Ferrite Rod J.W. Miller (310) 515-1720 http://www.jwmiller.com/ CoilCraft (847) 639-6400 http://www.coilcraft.com/ J.W. Miller (310) 515-1720 http://www.jwmiller.com/ J.W. Miller (310) 515-1720 http://www.jwmiller.com/ 6702 Bishop Electronics Corp. (562) 695 - 0446 http://www.bishopelectronics.com/ Nichicon Corp. (847) 843-7500 http://www.nichicon-us.com/ BEC-9950 A11A-50V QAF2Exx or QAS2Exx Supplier/Contact Information Supplier Part #
CBYP
1.0F - 10F
CBYP D1 L1
1.0F - 10F 1A, 50V 25H, 5A
L1
47H, 5A
PCV-0473-05
L1
50H, 5.6A
5504
L1
68H, 7.3A
5512
www.national.com
16
LM4651 & LM4652
Application Information
(Continued)
10127764
FIGURE 7. Reference PCB Schematic
17
www.national.com
LM4651 & LM4652
Application Information
(Continued)
10127781
FIGURE 8. Reference PCB Silk Screen Layer
10127780
FIGURE 9. Reference PCB Silk Screen and Solder Mask Layers
www.national.com
18
LM4651 & LM4652
Application Information
(Continued)
10127782
FIGURE 10. Reference PCB Top Layer
10127779
FIGURE 11. Reference PCB Bottom Layer
19
www.national.com
LM4651 & LM4652
Application Information
Symbol RFL1 RFL2 RFL3 RF R1 R2 RLP ROFFSET RDLY RSCKT ROSC Value 620k 62k 0 1M 4.7k 4.7k 2.2k 0 5.1k 39k 6.8k Tolerance 1% 1% 1% 1% 1% 1% 1% 1% 10% 10% 10%
(Continued) Bill of Materials for Reference PCB Type 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt 1/8 - 1/4 watt # per Board 2 2 2 1 1 1 1 0 1 1 1 Can also use as a 5.6k resistor # per Board 1 1 1 0 2 2 6 6 3 1 1 0 2 1 2 2 0 ** NOT USED ** Shorting Jumper Supplier/Comment Part #
All Caps. are Radial lead except CBYP, C1. Symbol CIN CLP CF CFL1 CFL2 CBT CB1 CB2 CB3 CB4 CStart C1 C2 CBYP CSBY1 CSBY2 CSBY3 Value 1F 0.47F 470pF 0 100pF 0.1F 0.1F 1F 0.001F 47F 1.5F 0 1F 4.7F 4,700F 0.1F 0 Tolerance 10% 10% 5% 5% 5% 10% - 20% 10% - 20% 10% 10% - 20% 10% - 20% 10% 10% 10% Type Metal Polyester Metal Polyester Ceramic Disc Ceramic Disc Ceramic Disc Monolithic Ceramic Monolithic Ceramic Tantalum Radial lead Monolithic Ceramic Electrolytic Radial Tantalum Radial lead Metal Polyester Metal Polyester Electrolytic Radial Ceramic Disc Voltage 100V 25V 25V 25V 25V 100V 100V 35V 100V 16V 25V 25V 25V 50V 25V 25V 50V Supplier/Comment Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 ** NOT USED ** Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 ** NOT USED ** Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 Digi-Key (800) 344-4539 ** NOT USED ** EF1105-ND EF1475-ND P5637A-ND P4201-ND Part # EF1105-ND EF1474-ND 1321PH-ND 1319PH-ND 1313PH-ND P4924-ND P4924-ND P2059-ND P4898-ND P914-ND P2044-ND
10% - 20% Metal Polyester 20% 20%
10% - 20% Mylar Axial lead
One or more pairs of coils from the list below is included with the reference PCB.
www.national.com
20
LM4651 & LM4652
Application Information
Symbol Value Tolerance
(Continued)
Bill of Materials for Reference PCB (Continued) Type High Current Toroid with Header Ferrite Bobbin Core Ferrite Core Voltage # per Board 2 Supplier/Comment J.W. Miller (310) 515-1720 CoilCraft (847) 639-6400 http://www.coilcraft.com J.W. Miller (310) 515-1720 Part #
L1
25H
15%
5.5 amp
6702
L1 L1
47H 50H
10% 10%
5.0 amp 5.6 amp
2 2
PVC-2-473-05 5504
Symbol S1 Standoffs RCA Input Banana Jack Heat sink D1
Description (SPDT) on-on, switch for STBY Plastic Round, 0.875", 4-40 PCB Mount Banana jack BLACK Wakefield 603K, 2" high X 2" wide, ~ 7C/W 1A, 50Volt Schottky (40A surge current, 8.3mS)
# per Board 1 4 1 5 1 4
Supplier/Comment Mouser (800) 346-6873 Newark (800) 463-9275 Mouser (800) 346-6873 Mouser (800) 346-6873 Newark (800) 463-9275 Digi-Key (800) 344-4539
Part # 1055-TA2130 92N4905 16PJ097 164-6218 58F537 (603K) SR105CT-ND
Additional Formulas for Reference PCB: Pole due to CIN: f3dB = 1/[2(R1 + RLP)CIN] or CIN = 1/[2(R1 + RLP)f3dB] Pole due to RLP and CLP: f3dB = 1/[2(R1 // RLP)CLP] or CLP = 1/[2(R1 // RLP)f3dB] where: (R1 // RLP) = 1/[1/R1 + 1/RLP] Gain for Reference PCB: Gain = {[R2/(R1 + 100 + Rlp)] x [(Rfl1 + Rfl2)/Rfl2] - [R2/(R1 + 100 + Rlp)] + 0.5} + [(VCC - 20) * 0.0175]
21
www.national.com
LM4651 & LM4652
Physical Dimensions
inches (millimeters) unless otherwise noted
Order Number LM4651N NS Package Number N28B
Isolated TO-220 15-Lead Package Order Number LM4652TF NS Package Number TF15B
www.national.com
22
LM4651 & LM4652 OvertureTM 170W Class D Audio Power Amplifier Solution
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
Non-Isolated TO-220 15-Lead Package Order Number LM4652TA NS Package Number TA15A
LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
National Semiconductor Asia Pacific Customer Support Center Fax: 65-6250 4466 Email: ap.support@nsc.com Tel: 65-6254 4466
National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: nsj.crc@jksmtp.nsc.com Tel: 81-3-5639-7560
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

▲Up To Search▲

Price & Availability of LM4651N

	To Download LM4651N Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .